Ensure reliability of your critical applications and minimize downtime with the T-APS Series. With the T-APS T-1 / E-1 automatic protection switches, you can quickly restore critical lines and equipment by easily switching over to redundant services.

Self-Contained, Standalone & Rack Mount

Ideal for Customer Premise, Remote Site and Data Center Applications

Line and Equipment Protection

Establish redundant links, or failover to standby routers and Channel Banks

T1 and E1 interface selectable

Select Interface type and all parameters

1+1 and 1:1 APS Protection Modes

1+1 Mode transmits on both primary and standby link simultaneously. 1:1 Mode transmits on active link only

Selectable switching activation thresholds

Define failover parameters. Monitors both active and standby circuits and switches to best available

Selectable line validation thresholds

Switchback only to known good circuit or device

CPE check to prevent false switching

Prevents false switching when common CPE is faulty

Configurable via front panel or RS-232 port

Craft port allows on-site access and Out-of-Band management

Fail-Soft Power Loss Cutover

Active path remains functional when switch loses power

SNMP Manageable

Integrate into your newtwork management scheme

Dual Power Inputs

48 VDC and 90 ~ 250 VAC power input (DC Priority)

Screenshots of T-APS Series Fully Automatic T-1/E-1 Protection Switching

  • Dataprobe electronic device on a white background

    T-APS Standalone Version

    Ideal for Customer Premise Locations
    Redundant A/C and 48VDC Powered T-APS

  • An close-up of an automatic protection switch Dataprobe T-PS-R of gray, with one of its partially extracted green circuit plates. The device has 16 slots, each with LED indicators, and the "intf" label under them. To the right, the word "MCU" is observed

    T-APS-R Rack Mount Card

    Complete T-1 / E-1 Protection Switch in 1 Card T-APS-R

  • An close-up of an automatic protection switch Dataprobe T-PS-R of gray, with one of its partially extracted green circuit plates. The device has 16 slots, each with LED indicators, and the "intf" label under them. To the right, the word "MCU" is observed

    T-APS Card Chassis

    Holds up to 15 T-APS-R Cards 48 VDC Powered
    A/C Power Supply Optional T-APS-R-15

  • Black power adapter with multiple cables on a white background

    A/C Power Supply for Nest

    A/C Power for Nest T-APS-R-15 Worldwide 110 – 250 VAC Up to 2 per T-APS-R-15 for Redundancy NOT Required for T-APS Standalone PS-48-WRI

1 of 4

T1 Interface

Line Code: AMI B8ZS

Frame Format: SF ESF Unframed

Bit Rate: 1.544M b/s

Impendance: 100 Ohms Resistive Balanced

Input Level: 0-36 dB

Output Level: 6V p-p

Line Build Out: 0-655 feet

E1 Interface

Bit Rate: 2.048 M b/s

Line Code: AMI HDB3

Frame Format: CCS CAS CCS+CRC CAS+CRC Unframed

Impendance: 120 Ohms Resistive Balanced

Input Level: 0-43 dB

Output Level: 6V p-p

Line Build Out: 0-655 feet

LED Indicators

Run: System Operational

Master: Master/Slave Configuration Status

T1: System Configured for T1

E1: System Configured for E1

L1: Line 1 Selected / Operational

L2: Line 2 Selected / Operational

LOS: Loss of Signal Indicator

OOF: Out of Frame Indicator

AIS: Alarm Indication Signal

RAI: Remote Alarm Indicator

Failure: System Failure Indicator

LPBK: Loopback Indicator

ACO: Alarm Acknowledgment Indicator

Programmable Parameters Automatic Switching

Code Violation: Fail: 1×10⁻³ to 1×10⁻⁷
Qualify: 1×10⁻⁵ to 1×10⁻⁹

CRC Error: Fail: 1×10⁻¹ to 1×10⁻⁵
Qualify: 1×10⁻³ to 1×10⁻⁷

Frame Error: Fail: 1×10⁻¹ to 1×10⁻⁵
Qualify: 1×10⁻³ to 1×10⁻⁷

AIS: Unframed or Framed

Loss of Signal:

Fault Duration: 500 ms, 1000 ms, 1500 ms, 2000 ms

Recovery Qualify Time: 0–98 Minutes, None

Console Port

RS-232 D9 DTE: VT100

9600 bps, 8 Data Bits, 1 Stop Bit, No Parity (9600, 8, N, 1)

Power

90–250V AC 47–63Hz and -48V±5V DC. Simultaneous use with DC priority

Weight

2.5 Lbs

Dimensions

8″ W × 2.75″ H × 9.5″ D

Operating Temperature

0ºC – 50ºC

Relative Humidity

0% – 90%

Regulatory Compliance

FCC Part 15 Class A

Reliability

MTBF 44,000 hrs

T-APS – END TO END PROTECTION

T-APS – End to End Protection

Protect your T-Span with a pair of automatic protection switches. Both links are continuously monitored and the switches coordinate switching, so you are never out of sync. Use a rack mounted, multi-switch system at the host location and standalone units at the customer premise or remote office.

T-APS – REDUNDANT CPE EQUIPMENT

T-APS – Last Mile Redundancy

If you have redundant feeds to your facility these switches will insure you are always on the best option. Both feeds are monitored you set the parameters for automatic switching. Of course you always have control via network management.

T-APS – REDUNDANT CPE EQUIPMENT

T-APS – REDUNDANT CPE EQUIPMENT

The T-APS series protects redundant equipment as well as redundant T-Spans. Back-up redundant routers, channel banks, or call center systems with these layer 1 reliable switches. Let Dataprobe application engineering show you how to integrate system reliability into any system.

  • Backup Switching On Autopilot

    T-APS switches make redundancy switching easy. The T-APS continuously monitors T-1 or E-1 circuits and switches to the operational path, and provides automatic failover switching between redundant lines.

    Designed for both line protection and equipment redundancy, the T-APS is ideal for any T-1 and E-1 networks where downtime is not an option. With the T-APS in control, you can have peace of mind that your critical applications will stay up and running.

  • Simple Programming to Onsite Applicaitons

    The T-APS is ideal for small offices and customer premise applications. It’s a self-contained, standalone unit capable of being powered by A/C or 48VDC sources, and line connections are standard RJ45 T1 and E1 (120 Ohm) connections. The T-APS features complete manageability via terminal or SNMP manager, plus status relay alarms.

    With the T-APS, small offices can enjoy the same T-1 / E-1 circuit protection as larger enterprises.

  • Multiple Circuit Switching Options

    With the T-APS rack mount card and chassis system, you can provide T-1 / E-1 protection to multiple circuits. All of the features of the standalone T-APS are supported in the card version, but up to 15 primary/redundant circuits can be supported.

    Each T-APS-R card provides a complete independent T-1 / E-1 protection switch, and all cards are managed from one network or serial interface with simple web pages and telnet menus.

    The chassis supports either 48VDC or 120/240 VAC with external power supplies. T-1 / E-1 terminations are via RJ45 Modular Jacks.

1 of 3